EFEgoFilemanualHome / Manuals / Bosch Professional GSR 18V-55Add product
MANUFACTURER RECORD 00102 OF 3,210,000

Bosch Professional
GSR 18V-55

Confirm the exact tool variant, power source, guard, accessory rating and work-area controls before operation.

Construction toolsCordless drillEnglish · GlobalRevision 2026.1

English: Product names, model codes, official notices and manufacturer text remain in the language of the authoritative source. EgoFile interface content is translated.

DATA PROVENANCE

What this page contains

Record type
EgoFile product profile
Responsible source
Manufacturer
Verification
Editorial content
Source evidence
Identification based on an official source
Last source check
1 August 2026
Indexing policy
Noindex — no complete OEM manual
Important limitation

This profile helps identify the product but does not replace the manufacturer's manual.

No manual content copied
80%profile completeness
PRODUCT WORKSPACE

One product. Everything in one place.

Editorial product profile. Confirm the complete rating-label code before saving a serial number or following variant-specific instructions.

Exact brand and modelProduct categoryMarket and languageNamed sourceOfficial identifier
01Confirm the variant

Compare the complete model, regional suffix and label.

02Save and monitor

Keep warranty, history and safety alerts together.

03Get a safe answer

Use cited guidance or create a private EgoFile case.

Add to My devicesAsk about this product →
01
Quick start

Before first use

  1. Inspect the tool, cable or battery and all guards.
  2. Fit only an accessory rated for the tool and task.
  3. Secure the workpiece and prepare dust, noise and eye protection.
02
Daily use

Operate the product correctly

  1. Use both hands and the specified auxiliary handle where provided.
  2. Keep the tool within its rated duty and accessory speed.
  3. Remove the battery or unplug before adjustments or clearing jams.
03
Safety

Important precautions

  • Never bypass a guard, brake or interlock.
  • Check for hidden wiring, pipes and structural hazards before cutting or drilling.
  • Stop immediately for kickback, smoke, damaged insulation or abnormal vibration.
04
Maintenance

Maintain reliable operation

  • Clean ventilation slots without forcing debris inside.
  • Inspect chucks, guards, cables and battery contacts regularly.
  • Arrange qualified service for internal electrical or drive faults.
COMMON ISSUES AND SYMPTOMS

What the product may be indicating

These are general diagnostic paths for this product category. Error-code numbers differ between brands, markets and revisions, so EgoFile shows a code only after it is confirmed in the exact official manual.

Source policySafe checks are maintained by EgoFile and linked to the official source record. No third-party manual text is copied.
01POWER

Tool does not start

Medium priority

What it means: The supply, battery, lock-off or electronic protection may be preventing operation.

First safe check: Remove the accessory load, verify the power source and follow the documented reset.

Stop condition: Stop for damaged insulation, a swollen battery or repeated breaker trips.

02STALL

Accessory stalls or binds

High priority

What it means: The accessory, feed rate, material or selected mode may be unsuitable.

First safe check: Disconnect power, free the accessory and confirm its rating and installation.

Stop condition: Do not restart until the cause of binding and kickback has been removed.

03VIBRATION

Abnormal vibration or run-out

High priority

What it means: An accessory may be damaged, loose, unbalanced or incorrectly mounted.

First safe check: Stop immediately and inspect the accessory, flange, chuck and guard.

Stop condition: Replace damaged parts; never test a cracked abrasive wheel.

04HEAT

Overload or overtemperature

Medium priority

What it means: Blocked cooling, excessive load or duty-cycle limits may have activated protection.

First safe check: Switch off, clear external vents and let the tool cool naturally.

Stop condition: Request service for smoke, melting, smell or repeated shutdown.

QUICK CHECKS

Three additional checks

Use these checks when no error code is displayed.

Tool will not start

Check the battery, power source, lock-off and overload state.

Accessory stops

Disconnect power and check for binding or an unsuitable accessory.

Excess vibration

Stop and inspect the accessory, guard and spindle before reuse.

PUBLIC SAFETY CHECK

Check recalls separately from the manual.

No exact model match was attached automatically. Search the official safety records by brand, shorter model number or UPC.

Search safety notices →
Exact variant check

This EgoFile profile is a practical reference. Confirm the exact product and use the manufacturer document for operation, repair and safety-critical work.

Manufacturer support →
← Previous recordAll records: 3,210,000Next record →