EFEgoFilemanualHome / Manuals / Hilti PM 30-MGAdd product
MANUFACTURER RECORD 00125 OF 3,210,000

Hilti
PM 30-MG

Verify calibration status, environmental limits and the reference surface before relying on a measurement.

Construction toolsLaser levelEnglish · GlobalRevision 2026.1

English: Product names, model codes, official notices and manufacturer text remain in the authoritative source language. EgoFile interface labels are translated.

DATA PROVENANCE

What this page contains

Record type
Profil urządzenia EgoFile
Authority
Producent
Verification
Treść redakcyjna
Evidence
Identyfikacja na podstawie oficjalnego źródła
Last source check
1 sierpnia 2026
Indexing policy
Noindex — brak pełnej instrukcji OEM
Important limitation

Profil pomaga rozpoznać urządzenie, ale nie zastępuje instrukcji producenta.

Bez kopiowania instrukcji
80%profile completeness
PRODUCT WORKSPACE

One product. Everything in one place.

Editorial product profile. Confirm the complete rating-label code before saving a serial number or following variant-specific instructions.

Exact brand and modelProduct categoryMarket and languageNamed sourceOfficial identifier
01Confirm the variant

Compare the complete model, regional suffix and label.

02Save and monitor

Keep warranty, history and safety alerts together.

03Get a safe answer

Use cited guidance or create a private EgoFile case.

Add to My devicesAsk about this product →
01
Quick start

Before first use

  1. Inspect housing, optics, sensors and batteries.
  2. Select the correct unit, mode and reference point.
  3. Perform the documented self-check or calibration confirmation.
02
Daily use

Use the product correctly

  1. Protect the instrument from impact, moisture and temperature shock.
  2. Repeat critical measurements from a second reference.
  3. Record tolerance, environment and instrument identity with the result.
03
Safety

Important precautions

  • Do not stare into laser beams or aim them at people or vehicles.
  • Use approved procedures near live electrical systems.
  • Do not rely on one detector reading before drilling or cutting.
04
Maintenance

Keep it working reliably

  • Clean optics with suitable non-abrasive materials.
  • Store dry in its case and remove batteries for long storage.
  • Arrange calibration after impact, drift or the specified interval.
COMMON ERRORS & SYMPTOMS

What the product may be telling you

These are category-level diagnostic paths. Error-code numbers differ between brands, markets and revisions, so EgoFile shows a code only after it is confirmed in the exact official manual.

Source policySafe checks are maintained by EgoFile and linked to the official source record. No third-party manual text is copied.
01NO READING

No measurement is available

Low priority

What it means: Range, mode, target conditions or power may be unsuitable.

Safe first check: Confirm mode, reference, batteries and the stated operating range.

Stop condition: Do not proceed with drilling or cutting on an uncertain detector result.

02UNSTABLE

Reading changes or will not settle

Medium priority

What it means: Movement, glare, temperature, surface or interference may affect the sensor.

Safe first check: Stabilise the instrument and repeat from a controlled reference.

Stop condition: Use an independent method before a safety-critical decision.

03CAL

Calibration warning or suspected drift

High priority

What it means: Impact, time or environmental change may have moved the instrument outside tolerance.

Safe first check: Stop relying on results and perform the documented field check.

Stop condition: Send the instrument for calibration when the check fails.

04LASER

Laser or optical output is not visible

Medium priority

What it means: Mode, receiver setting, brightness or contamination may be responsible.

Safe first check: Check the selected mode and clean optics using the approved method.

Stop condition: Never look into the aperture or open the optical housing.

QUICK CHECKS

Three more things to verify

Useful when no error code is visible.

No reading

Check batteries, mode, range and target conditions.

Reading is unstable

Stabilise the instrument and reduce glare, vibration or temperature change.

Calibration warning

Stop relying on results and complete the official verification procedure.

PUBLIC SAFETY CHECK

Check recalls separately from the manual.

No exact model match was attached automatically. Search the official safety records by brand, shorter model number or UPC.

Search safety notices →
Exact variant check

This EgoFile profile is a practical reference. Confirm the exact product and use the manufacturer document for operation, repair and safety-critical work.

Manufacturer support →
← Previous recordAll records: 3,210,000Next record →