EFEgoFilemanualHome / Manuals / Siemens SN63HX60CE/38Add product
INSTRUCTION PAGE 00026 OF 3,210,000

Siemens
SN63HX60CE/38

Confirm ventilation, power and water requirements before first use, then complete the manufacturer's initial cleaning procedure.

AGDDishwasherFrançais · FRRevision 2026.1

Français: Product names, model codes, official notices and manufacturer text remain in the language of the authoritative source. EgoFile interface content is translated.

DATA PROVENANCE

What this page contains

Record type
Manufacturer manual
Responsible source
Manufacturer / official support centre
Verification
Catalogued source
Source evidence
OEM document or official support page
Last source check
1 August 2026
Indexing policy
Page is eligible for indexing
Important limitation

Confirm the document scope and regional variant against the rating label.

Link to the document owner
100%profile completeness
PRODUCT WORKSPACE

One product. Everything in one place.

Manufacturer manual. Confirm the complete rating-label code before saving a serial number or following variant-specific instructions.

Exact brand and modelProduct categoryMarket and languageNamed sourceManufacturer documentation
01Confirm the variant

Compare the complete model, regional suffix and label.

02Save and monitor

Keep warranty, history and safety alerts together.

03Get a safe answer

Use cited guidance or create a private EgoFile case.

Add to My devicesAsk about this product →
01
Quick start

Before first use

  1. Remove packaging, films and transport parts.
  2. Place or install the appliance with the required clearances.
  3. Complete the first-use rinse, heat or calibration cycle.
02
Daily use

Operate the product correctly

  1. Use cookware, accessories and consumables approved for the appliance.
  2. Select the programme or temperature before starting.
  3. Allow hot surfaces and steam to dissipate before unloading.
03
Safety

Important precautions

  • Do not block ventilation openings.
  • Disconnect power and water before maintenance.
  • Use heat protection when handling hot trays, vessels or steam.
04
Maintenance

Maintain reliable operation

  • Wipe food residue after the appliance cools.
  • Clean filters, seals and removable accessories regularly.
  • Descale water systems at the interval shown by the appliance.
COMMON ISSUES AND SYMPTOMS

What the product may be indicating

These are general diagnostic paths for this product category. Error-code numbers differ between brands, markets and revisions, so EgoFile shows a code only after it is confirmed in the exact official manual.

Source policySafe checks are maintained by EgoFile and linked to the official source record. No third-party manual text is copied.
01START

Programme will not start

Low priority

What it means: The door latch, water supply, control lock or delay timer may prevent operation.

First safe check: Close the door, open the tap and cancel control lock or delay start.

Stop condition: Request service if the latch does not hold.

02FILL

No water enters

Medium priority

What it means: The inlet hose, tap or inlet filter may be restricted.

First safe check: Inspect the visible hose and confirm the water tap is fully open.

Stop condition: Stop if the inlet hose or safety valve is damaged.

03DRAIN

Water remains after the cycle

Medium priority

What it means: Filters, the drain hose or sink connection may be blocked.

First safe check: Clean removable filters and check the accessible drain connection.

Stop condition: Request service if the pump runs continuously or water returns.

04RESULT

Dishes remain dirty or wet

Low priority

What it means: Loading, spray-arm movement, programme choice or consumables may be unsuitable.

First safe check: Reload without blocking spray arms and verify salt, rinse aid and detergent settings.

Stop condition: Request service if water is not heating.

05LEAK

Leak protection is active

High priority

What it means: Water may have reached the base or an inlet component may have failed.

First safe check: Switch off, close the tap and leave the appliance level.

Stop condition: Do not tilt or restart the appliance; arrange qualified service.

QUICK CHECKS

Three additional checks

Use these checks when no error code is displayed.

No power

Check the socket, breaker and control lock.

Poor result

Verify loading, programme, consumables and cleaning status.

Unusual noise

Stop the appliance and check for loose accessories or foreign objects.

PUBLIC SAFETY CHECK

Check recalls separately from the manual.

No exact model match was attached automatically. Search the official safety records by brand, shorter model number or UPC.

Search safety notices →
Exact variant check

This EgoFile page is a practical quick reference, not a replacement for the complete manufacturer document. Confirm the full model, configuration and regional suffix before installation, operation, repair or safety-critical work.

Manufacturer support →
← Previous recordAll records: 3,210,000Next record →